Euroseam

Jump to:
Technical & Downloads
Sustainability
Services

Euroclad_Euroseam_Roof_Poultons_Park_Romsey_3-1

Euroclad_Euroseam_Roof_Poultons_Park_Romsey_5-1

Euroseam is a standing seam cladding profile that can create remarkable curves and rollformed tapers

Euroseam is manufactured as roof or wall cladding sheets or as part of an Elite System providing you with flexibility and creative freedom to achieve a wide range of designs.

A range of waveform, concave and convex shapes can be achieved, with precision tapers manufactured at Euroclad and rollformed curves with a radius as small as eight metres.

Euroseam® can be used to achieve a whole range of curves from large barrel vaults to details at the eaves or even covered walkways and canopies. The sheets can be formed into sinusoidal curves or can even use tapered sheets to produce domes
Euroseam Standing Seam Roofing Systems can be purchased with a system guarantee up to 25 years when installed as an Elite System
Rooflights are available to as part of the Elite System package
Our typical twin skin standing seam roof with a 0.7mm liner, insulation to achieve 0.25 U value and 0.9mm aluminium standing seam will give a sound reduction of 41db, and can be enhanced to provide greater preformance

On Site Rolling

Euroseam can be rollformed and curved onsite, it can even be rollformed at the eaves of the building, delivering finished product directly onto the roof as it is being installed.

Where sheet length exceeds 18.5 metre lengths we recommend the use of our mobile production units, where standing seam profiles can also be produced from one of our 3 mobile units.
The Euroclad On Site team can arrive to site and produce sheets following a 10 minute simple trailer setup. Sheets can be rollformed then lifted using a Euroclad Spreader beam or alternatively the rollformer can be safely lifted to the eaves and sheets produced at roof level.
The rollformer has its own wireless remote control unit so the machine can be run from the safety of the roof area without being inside the rollformer production unit. When rolling at ground level we can produce 6000lm of sheets per day, at roof level we can also produce 6000lm per day.

Technical & Downloads

Product Parameters

Find our specific system detail files here>

STUCCO – Euroseam 400 0.9mm
PARAMETER DESCRIPTION	LIMITS
Maximum sheet length:	No limit
Minimum sheet length: Straight sheets - Induced curves -	0.5 metres 2 metres
Minimum self-curve concave radii:	60 metres
Minimum self-curve convex radii:	45 metres
Minimum induced smooth curve concave radii: (*1)	8 metres
Minimum induced smooth curve convex radii: (*1)	8 metres
Minimum transition straight length on complex curves with any radii below 15 metre: (*2)	1 metre

PAINTED ARS/PVDF – Euroseam 400	0.9mm	1.2mm (standard alloy)
PARAMETER DESCRIPTION	LIMITS
Maximum sheet length:	No limit
Minimum sheet length: Straight sheets - Induced curves -	0.5 metres 2 metres
Minimum self-curve concave radii:	60 metres
Minimum self-curve convex radii:	45 metres
Minimum induced smooth concave curve radii:	15 metres	8 metres
Minimum induced smooth convex curve radii:	15 metres	8 metres
Minimum transition straight length on complex curves with any radii below 15 metre: (*2)	1 metre

NOTE:

(*2)We advise all complex curves that have radii less than 15 metres be site curved, so that fit to structure can be ascertained.
Induced curved sheets will always have a minimum 500mm of straight leg on one end of the supplied sheet as a result of the manufacturing process. This straight may be a problem on tight radii short sheets and as such please seek advice from Euroclad should you have any concerns. All smooth curves are supplied to the following tolerance;
- > 15 metre radii curves +/- 0.5 metres on radii
- > 8 and < 15 radii curves +/- 0.35 metres on radii
- Positional / length of curved / straight sections +/- 200mm

Euroseam Tapers 0.9mm
PARAMETER	LIMITS	COMMENT
Maximum length:	10 metres	Tapers can only be delivered (not site rolled)
Minimum length:	2 metres
Maximum standard width: (*3)	395 mm’s	This is ordered size between halter centre lines.
Minimum width:	167 mm’s	This is ordered size between halter centre lines.
Self-curve radii:	50 metres	Note that this type of installation is “skill” based and no setting details can be supplied, but advice can be sought by contacting our Technical department.

We can manufacture tapers 200mm longer (100 mm each end) than ordered length for Vieo and Euroseam tapers to aid installation, for which no charge is applied. Should this not be required then this must be advised upon your order.
(*3) – We can manufacture sheets over this width, up to 490mm but an additional charge for scrap material and a longer lead time will be applicable. We cannot supply technical support for sheets with a pan width over 500mm.

Find our specific system detail files here>

Material Options

PVDF COATED ALUMINIUM
Various colour coatings are available for the aluminium material our preferred choice is PVDF. PVDF, (polyvinylidene Fluoride) coatings were developed over 30 years ago, the surface finish is smooth.
This comprises a minimum of 70% PVF2 resin and a maximum of 30% acrylic. It is very durable, giving excellent flexibility and chemical resistance combined with the highest possible performance regarding gloss retention, chalking and colour change.
Please note that there is a minimum order quantity for all painted aluminium material.
For full colour availability and options please contact us.

ORGANIC PATINA ALUMINIUM
Planning constraints sometimes require a "dull" finish to the mill finish aluminium because of the reflectivity of new stucco embossed aluminium. In these instances an Organic Patina finish utilising a low gloss dull lacquer is available which offers similar reflectivity properties of weathered aluminium.

Wind Load Tables / Data Sheets

Design Files - Details

PDF

Euroclad_Euroseam_Profile_ESN124_400_Roof

Download Download

DWG

Euroclad_Euroseam_Profile_ESN124_400_Roof_Profile

Download Download

Sustainability

Planet Passionate

Our Approach to Sustainability

Euroclad Group is committed to continual improvement, striving to manufacture and deliver the most environmentally responsible and sustainable products. Key to this is establishing, implementing and maintaining an Integrated Management System which complies with the requirements of ISO9001, ISO14001.

Euroclad Group aims to make specifying the most sustainable products simpler and more transparent. To this end it has implemented BES 6001 Responsible Sourcing of Construction Products standard that independently demonstrates that a building material has been produced in a way that has minimised its environmental impact and is sustainable.

ISO14001 - Euroclad Group

Download PDF (0.3MB) Download PDF (0.3MB)

ISO 9001 Euroclad Group

Download PDF (0.3MB) Download PDF (0.3MB)

BES 6001 Euroclad Group

Download PDF (1.1MB) Download PDF (1.1MB)

Services

Complementary Products

Contact Us

Contact details for Euroclad Team